Dancette, S.
[UCL]
Delannay, Laurent
[UCL]
Jodlowski, T.
[Ecole Polytechnique Fédérale de Lausanne (EPFL) - Institute of Mechanical Engineering, Lausanne, Switzerland]
Giovanola, J.
[Ecole Polytechnique Fédérale de Lausanne (EPFL) - Institute of Mechanical Engineering, Lausanne, Switzerland]
Twinning is commonly observed above a certain level of deformation at room temperature in face centred cubic (fcc) metals with low stacking fault energy (SFE). Twins carry a part of the plastic deformation and they act as barriers to dislocation motion, leading to anisotropic hardening already at the crystal level. The influence of deformation twinning on the development of texture and the related anisotropy and hardening is investigated in this study by means of experimental observations as well as an advanced crystal plasticity model. The latter "multisite" model takes account of short range interaction among adjacent grains. Anisotropy is assessed based on mechanical tests in uniaxial tension and torsion. When simulation of torsion rely on a simplified one-dimensional finite element modeling, the crystal plasticity model yields qualitative predictions of the strengthening, the texture development and the Swift effect. More accurate predictions would require three-dimensional simulation of the torsion test. © 2010 Springer-Verlag France.
- S. Mahajan and G.Y. Chin. Twin-slip, twin-twin and slip-twin interacions in co-8 fe alloy single crystals. Acta. Metall., 21:173–179, 1973.
- M. Dao, L. Lu, Y.F. Shen, and S. Suresh. Strength, strain-rate sensitivity and ductility of copper with nanoscale twins. Acta. Mat., 54:5421–5432, 2006.
- T. Leffers and R.K. Ray. The brass-type texture and its deviation from the copper-type texture. Prog. Mat. Sci, 54:351–396, 2009.
- F. Montheillet, P. Gilormini, and J.J. Jonas. Relation between axial stresses and texture development during torsion testing: A simplified theory. Acta Metall., 33:705–717, 1985.
- L.S. Toth, J.J. Jonas, D. Daniel, and J.A. Bailey. Texture development and length changes in copper bars subjected to free end torsion. Textures Microstruct., 19:245–262, 1992.
- L. Anand and S.R. Kalidindi. The process of shear band formation in plane strain compression of fcc metals: Effects of crystallographic texture. Mech. Mater., 17:223–, 1994.
- G.I. Taylor. Plastic strain in metals. J. Inst. Metals, 62:307–324, 1938.
- P. Van Houtte, S. Li, M. Seefeldt, and L. Delannay. Deformation texture prediction: from the taylor model to the advanced lamel model. Int. J. Plast., 21:589–624, 2005.
- S.R. Kalidindi. Incorporation of deformation twinning in crystal plasticity models. J. Mech. Phys. Solids, 46:267–290, 1998.
- M. Melchior. Modelling of texture and hardening of TWIP steel - Advanced finite element representation of polycristalline aggregates. PhD thesis, Université Catholique de Louvain, 2009.
- L. Duchêne, F. El Houdaigui, and A.M. Habraken. Length changes and texture prediction during free end torsion test of copper bars with fem and remeshing techniques. Int. J. Plast., 23:1417–1438, 2007.
- E.C. Aifantis. The physics of plastic deformation. Int. J. Plast., 3:211–247, 1987.
Bibliographic reference |
Dancette, S. ; Delannay, Laurent ; Jodlowski, T. ; Giovanola, J.. Multisite model prediction of texture induced anisotropy in brass. In: International Journal of Material Forming, Vol. 3, no. SUPPL. 1, p. 251-254 (2010) |
Permanent URL |
http://hdl.handle.net/2078.1/163740 |